Intel I860

The Intel i860 (also known as 80860) is a RISC microprocessor design introduced by Intel in 1989. It is one of Intel's first attempts at an entirely new, high-end instruction set architecture since the failed Intel iAPX 432 from the beginning of the 1980s. It was the world's first million-transistor chip. It was released with considerable fanfare, slightly obscuring the earlier Intel i960, which was successful in some niches of embedded systems, and which many considered to be a better design. The i860 never achieved commercial success and the project was terminated in the mid-1990s.

Implementations

The first implementation of the i860 architecture is the i860 XR microprocessor (code-named N10), which ran at 25, 33, or 40 MHz. The second-generation i860 XP microprocessor (code named N11) added 4 Mbyte pages, larger on-chip caches, second level cache support, faster buses, and hardware support for bus snooping, for cache consistency in multiprocessor systems. A process shrink for the XP (from 1 μm to 0.8 CHMOS V) increased the clock to 40 and 50 MHz. Both microprocessors supported the same instruction set for application programs.

Technical features

The i860 combined a number of features that were unique at the time, most notably its very long instruction word (VLIW) architecture and powerful support for high-speed floating-point operations. The design uses two classes of instructions: "core" instructions which use a 32-bit ALU, and "floating-point or graphics" instructions which operate on a floating-point adder, a floating-point multiplier, or a 64-bit integer graphics unit. The system had separate pipelines for the ALU, floating-point adder, floating-point multiplier, and graphics unit. It can fetch and decode one "core" instruction and one "floating-point or graphics" instruction per clock. When using dual-operation floating-point instructions (which transfer values between subsequent dual-operation instructions), it is able to execute up to three operations (one ALU, one floating-point multiply, and one floating-point add-or-subtract) per clock.

All of the data buses were at least 64 bits wide. The internal memory bus to the cache, for instance, was 128 bits wide.

The "core" class instructions use thirty-two 32-bit integer registers. But the "floating-point or graphics" instructions use a register file that can be accessed by the floating point units as either thirty-two 32-bit, sixteen 64-bit, or eight 128-bit floating-point registers, or that can be accessed by the graphics unit as sixteen 64-bit integer registers.

The "core" unit is responsible for fetching instructions, and in the normal "single-instruction" mode can fetch one 32-bit "core" or one 32-bit "floating point or graphics" instruction per cycle. But when executing in dual-instruction mode, the instruction cache is accessed as VLIW instructions consisting of a 32-bit "core" instruction paired with a 32-bit "floating-point or graphics" instruction, simultaneously fetched together over a 64-bit bus.

Intel referred to the design as the "i860 64-Bit Microprocessor".

Intel i860 instructions acted on data sizes from 8-bit through 128-bit.

The graphics unit was unique for the era. It supported a number of commands for SIMD-like instructions in addition to basic 64-bit integer math. For instance, its 64-bit integer datapath can represent multiple pixels together as either 8-bit pixels, 16-bit pixels, or 32-bit pixels. Experience with the i860 influenced the MMX functionality later added to Intel's Pentium processors.

One unusual feature of the i860 was that the pipelines into the functional units were program-accessible (VLIW), requiring the compilers to order instructions carefully in the object code to keep the pipelines filled. In traditional architectures these duties were handled at runtime by a scheduler on the CPU itself, but the complexity of these systems limited their application in early RISC designs. The i860 was an attempt to avoid this entirely by moving this duty off-chip into the compiler. This allowed the i860 to devote more room to functional units, improving performance. As a result of its architecture, the i860 could run certain graphics and floating-point algorithms with exceptionally high speed, but its performance in general-purpose applications suffered and it was difficult to program efficiently (see below).

Performance

On paper, performance was impressive for a single-chip solution; however, real-world performance was anything but. One problem, perhaps unrecognized at the time, was that runtime code paths are difficult to predict, meaning that it becomes exceedingly difficult to order instructions properly at compile time. For instance, an instruction to add two numbers will take considerably longer if those numbers are not in the cache, yet there is no way for the programmer to know if they are or not. If an incorrect guess is made, the entire pipeline will stall, waiting for the data. The entire i860 design was based on the compiler efficiently handling this task, which proved almost impossible in practice. While theoretically capable of peaking at about 60-80 MFLOPS for both single precision and double precision for the XP versions, manually written assembler code managed to get only about up to 40 MFLOPS, and most compilers had difficulty getting even 10 MFLOPs. The later Itanium architecture, also a VLIW design, suffered again from the problem of compilers incapable of delivering sufficiently optimized code.

Another serious problem was the lack of any solution to handle context switching quickly. The i860 had several pipelines (for the ALU and FPU parts) and an interrupt could spill them and require them all to be re-loaded. This took 62 cycles in the best case, and almost 2000 cycles in the worst. The latter is 1/20000th of a second at 40 MHz (50 microseconds), an eternity for a CPU. This largely eliminated the i860 as a general purpose CPU.

Demise

As the compilers improved, the general performance of the i860 did likewise, but by then most other RISC designs had already passed the i860 in performance.

In the late 1990s, Intel replaced their entire RISC line with ARM-based designs, known as the XScale. Confusingly, the 860 number has since been re-used for a motherboard control chipset for Intel Xeon (high-end Pentium) systems and a model of the Core i7.

Andy Grove suggested that the i860's failure in the marketplace was due to Intel being stretched too thin:

Applications

At first, the i860 was only used in a small number of supercomputers such as the Intel iPSC/860. Intel later marketed the i860 as a workstation microprocessor for a time, where it competed with microprocessors based on the MIPS and SPARC architectures, among others. The Oki Electric OKI Station 7300/30 and Stardent Vistra 800 Unix workstations were based on a 40 MHz i860 XR running UNIX System V/i860. The Hauppauge 4860 and Olivetti CP486 featured an Intel 80486 and i860 on the same motherboard. Microsoft initially developed what was to become Windows NT on internally designed i860XR-based workstations (codenamed ''Dazzle''), only porting NT to the MIPS ( Microsoft Jazz), Intel 80386

HOME


Content is Copyleft
Website design, code, and AI is Copyrighted (c) 2014-2017 by Stephen Payne


Consider donating to Wikimedia



As an Amazon Associate I earn from qualifying purchases